Machinery Weight 55-72t
Max Feeding size(mm) ≤700mm
Hopper Volume(m³) /
Primary crushing begins when large rock is tipped or fed into the top of the machine. The feed opening accepts pieces sized within the crusher’s design range and directs them into the crushing chamber. That chamber is formed by two opposing surfaces: a fixed jaw plate mounted on the frame and a movable jaw plate that swings under drive from the eccentric mechanism. The space between them is wider at the top and narrows toward the bottom, so material is drawn into progressive compression rather than sitting in a parallel gap.
Feed opening dimensions set the largest piece that can enter without bridging. Openings that are too small force upstream breaking or rejection of oversize stone. Openings matched to the quarry or recycling feed allow a steady flow into the chamber and reduce the need for constant operator intervention at the hopper. Even feed distribution across the width of the jaws also matters: preferential loading on one side accelerates local wear and can raise peak loads on the moving jaw.
In operation the movable jaw advances toward the fixed jaw and then retreats in a continuous cycle. The approach phase clamps rock against the fixed plate; the retreat phase allows fragments to drop deeper into the chamber. This repeated approach-and-retreat motion is the source of the compression that breaks the feed. Stroke, kinematics and speed of the swing are fixed by the machine design and by how the discharge setting is adjusted for the job.
Rock trapped between the plates experiences rising compressive stress until internal cracks link up and the piece fails into smaller fragments. Hard, abrasive stone may need several nips before it is small enough to pass lower in the chamber; softer or well-jointed rock may fail in fewer cycles. The jaw plates do not cut like blades; they squeeze. Tooth or corrugation patterns on the plates help grip the stone and influence how fragments orient for the next compression. A Jaw Crusher for Rock application relies on that cyclic compression rather than on impact alone.
After each fracture event, gravity and the opening motion of the movable jaw let material migrate downward. Larger pieces remain higher until they are broken further; smaller pieces progress toward the discharge zone. Chamber geometry—angle between the plates, length of the crushing zone and profile of the liners—shapes that flow. Too steep a chamber can empty too quickly with insufficient reduction; too shallow a profile can choke with compacted fines. Balanced design keeps rock moving while still giving enough residence time for the required size reduction.
Once fragments are small enough to pass the gap at the bottom of the chamber, they fall through the discharge opening onto a conveyor or into a bin. The closed-side setting of that opening is the main machine adjustment for product top size. A wider setting raises throughput and coarsens the product; a tighter setting yields finer product at the cost of capacity and often of higher wear. Suitable discharge settings are chosen against the needs of the next stage—secondary crushing, screening or direct use—so that the jaw neither overworks the stone nor passes excessive oversize. Adjustment mechanisms must be set securely so that the gap does not drift under load.
The DC Series uses a chamber layout intended to guide feed from the opening through successive compression zones toward discharge. Chamber structure supports both the downward movement of broken stone and the repeated nips needed for hard feed. Feed entry and liner profiles are coordinated so that bridging is reduced and wear is spread more evenly along the plates when the machine is fed correctly.
Jaw motion is arranged to deliver the cyclic approach and retreat that define jaw crushing. That motion links to the high-efficiency intent of the series: sustained compression work on the rock with a mechanical arrangement suited to continuous primary duty. Actual kinematics and any toggle or eccentric details follow the product configuration for each model in the series.
Crushing loads transmit into the frame, bearings and main shafts. A Heavy Duty Jaw Crusher structure is built so that those loads remain within the capacity of the frame and rotating assembly during normal operation. Deep frames, robust side members and carefully seated bearings support stable alignment of the movable jaw. Structural stiffness limits excessive deflection that would open the discharge gap under peak loads and throw product size out of range.
Jaw plates take the direct abrasion and impact of the rock. Materials and profiles specified for the DC Series are chosen for that duty, with replacement liners intended to restore chamber geometry when wear advances. Durable plates extend intervals between liner changes; they do not remove the need for inspection schedules matched to rock abrasiveness and operating hours. Correct seating of new plates maintains the designed chamber shape after service work.
| Stage | What happens to the rock | Machine influence |
|---|---|---|
| Feeding | Oversize accepted into the chamber | Feed opening and hopper arrangement |
| First compression | Movable jaw nips rock against fixed plate | Stroke and plate profile |
| Further reduction | Fragments re-nipped as they move down | Chamber length and angle |
| Flow through chamber | Material migrates toward the bottom | Geometry and jaw retreat motion |
| Discharge | Product exits at set gap | Closed-side setting and adjustment security |
| Structural support | Loads carried by frame and bearings | Heavy-duty frame and wear liners |
Consistent feed without prolonged empty running or chronic overload keeps the crushing cycle stable. Tramp metal and uncrushable objects require protection systems where fitted, because they can damage plates and mechanical parts. Lubrication of bearings and inspection of toggle and tension components sustain the motion that creates compression. Operators and maintainers treat the chamber as a wear zone: plate thickness, fastening condition and discharge setting are checked on a plan matched to the site’s rock and throughput.
Inside a jaw crusher, rock enters through the feed opening, is repeatedly compressed between a fixed plate and a moving plate, migrates downward as it fractures and leaves through a discharge opening set for the required product size. The DC Series High Efficiency European Jaw Crusher supports that sequence through chamber design, jaw motion, heavy-duty structure and wear-resistant plates aimed at steady primary crushing duty. Shanghai Dongmeng Road and Bridge Machinery Co., Ltd. produces crushing equipment including jaw crusher configurations for rock processing applications. Review of feed size, product size targets, capacity needs and site conditions against the machine’s chamber and structural design supports selection of a jaw crusher that carries material cleanly from feed to discharge.
Machinery Weight 53-62t
Max Feeding size(mm) ≤600mm
Hopper Volume(m³) 80-360t/h
Machinery Weight 55-57t
Max Feeding size(mm) ≤215mm
Hopper Volume(m³) /
Machinery Weight 33-35t
Max Feeding size(mm) 150-400t/h
Hopper Volume(m³) 2.5
Machinery Weight 33t
Max Feeding size(mm) 150-400t/h
Hopper Volume(m³) 7m³
Machinery Weight 54-63t
Max Feeding size(mm) ≤600mm
Hopper Volume(m³) /
Machinery Weight 9.5-75t
Max Feeding size(mm) ≤1000mm
Hopper Volume(m³) 61-1204t/h
Just let we know what you want, and we will get in touch with you as soon as possible!